2006 Duramax

The 2006 Duramax 90 degree angled eight cylinder vee configuration turbodiesel uses a tough, compact cast-iron engine block featuring cross-drilled, 4-bolt bearing caps and induction-hardened cylinder bores, which is a procedure borrowed from bigger diesel engines. An aluminum die-cast lower crankcase gives added strength to the 2006 Duramax engine block and acts as a lower engine cover, eliminating extra weight. The 2006 Duramax's steel crankshaft is forged and the surface is hardened with an application of nitride while aluminum pistons reduce overall mass and increase efficiency. Each one one of the pistons in the 2006 Duramax is cast with a small hole in its skirt, permitting jets to direct cooling oil through a guide to the bottom portion of the piston bowl, where the majority of the heat is generated in the motor of a 2006 Duramax.

Advanced Technology In The 2006 Chevy Duramax

Structural changes were made in the late 2006 model year to the 2006 Duramax engine block and the connecting rods of the 2006 Chevy Duramax in order to increase the engine strength. This allowed changes to the calibration that improved the output for certain applications in the GMC Sierra and Chevrolet Silverado pickup trucks. In addition, a newly designed fuel pump has increased the fuel pressure in the 2006 Chevy Duramax from about 23,000 psi (approximately three hundred times better pressure than that provided by regular gasoline injection systems) to an astounding 26,000 psi.

Powerful 2006 Chevy Duramax Diesel

2006 Chevy Duramax Diesel's rails and fuel lines have also been strengthened to allow for the increased pressure. The engine of the 2006 Duramax Diesel saw its operating smoothness improved drastically by lowering the compression ratio from 17.5:1 to 16.8:1. The progression of development geared towards lowering diesel emission in the 2006 Chevy Duramax Diesel led to an enlarged exhaust gas recirculation (EGR) system being installed in every Duramax 6.6L V8.

Chevy 2006 Duramax 2500 Pickup Truck

The 2006 Duramax 2500's EGR system redirects some of the 2006 Duramax's exhaust gas back to the intake stream in order to reduce oxides of nitrogen emissions and cool combustion. The Duramax Diesel system has a distinctive cooling process that enhances its effectiveness. Required hardware in the 2006 Duramax 2500 includes plumbing that directs some of the turbocharger exhaust gas to the intake, a stainless steel cooling device and a control valve for the EGR system, as the EGR valve in the 2006 Duramax is regulated by the E35 engine control module.

The Durable 2006 2500HD Duramax Chevy Truck

The EGR elements for cooling in the 2006 2500HD Duramax are bolted onto the right engine side, inboard of the cylinder head, and include jackets fed by the engine coolant. Exhaust gas generated by the 2006 Duramax that is returned ends up passing through a spiral of passages in the element, where its temperature is lowered before returning to the combustion chamber of the 2006 Duramax. This is just one of General Motors' remarkable technological innovations which have marked the production of the superlative 2006 2500HD Duramax pickup truck by both GMC and Chevrolet divisions.

2006 Duramax 4X4 Goes Anywhere

The 2006 Duramax cylinder heads made of aluminum deliver strength that is equal to or greater than those made from cast-iron, with the added benefit of being considerably less in weight which is of particular interest to 2006 Duramax 4X4 owners. Light weight is critical not only to off roading but also to maintain the power to weight ratio at an optimum level in the 2006 Duramax. Each Duramax Diesel cylinder has four valves, which has become fairly standard for most off roading diesels like the 2006 Duramax 4X4, as well as an incorporated oil cooler to keep the engine from frying on steep, slow desert grades.